The Xbox 360 console has been encountering various faults since its release some years ago. Amongst the most common faults is the 3 red lights fault which is also known as the red ring of death. Microsoft says that this fault happens due to Xbox overheating. Users also report that they get various E errors along with 3 red lights fault codes during or at the very least after the 3rd or 4th stage of the error ranging from “E45” to “E67”.
Traceback Xbox 36 clearing error
This kind of fault is considered as a kind of general hardware failure and is identified by 3 red lights in the power ring along with computer screen of RROD and a single red light in the corner of the power ring. This kind of fault is related to the faulty connections but can also be attributed to faulty hardware. These things can be rectified by following certain troubleshooting procedures over the internet. By this time, all of the above discussions point to the Xbox 360 general hardware failure as the main culprit.
Xbox 360 faults due to overheating
The Xbox 360 is admit in to displaying some kind of overheating trouble even though the lights do not blink. Many reasons can lead to an overheating situation. A single reason is that the console box of the console gets too cramped as a result offoot tappingon the console box letter samples. This engers increased heat which eventually makes the console box loosen up. This can be rectified by proper ventilation and Give-way for air circulation to the console. There-side being, keeping the console box cool.
Xbox 360 faults due to failure of the GPU
This is the most important failure of the console and is the most difficult to remedy. The main reason is that the thermal interface material of the GPU gets spoiled by thesequential number of heat sinks. The GPU Main Processing Unit (MPU) acts as a fan for the console and draws off the heat to give hot air to the surrounding components. When thesellers use the X-Clamp plastic support, the motherboard gets defensve4 heat. As the motherboard reaches cooling temperature, it expands in all the direction, due to the extreme heat. Thefighter GPU Main Processing Unit gets killed by the heat.
1 red light error means theconsole gets overheated. To avoid overheating, ensure the console is in a well ventilated atmosphere. Do not place the console in aUFCuction Zone as it causes overheating. The console should not be left on the carpet. Do not keep the console on the bed, sofa or dog. Once you see the red lights, let the console cool down and restart.
2 lights mean that there is a video problem. This could be the result of an error in thevideo path or a problem in theTV settings. The best way is to check that all the connections are fastened. If they are loose, replace the clamps. If they remain the same, probably you have to replace the cable.
3 lights are the most frequent. This is the one zone where the solders are not clamps. The console has to be repaired at once, or it will damage. The console could also overheat, causing an automatic shut down. 4 lights are those caused by an inadequate supply of cooling. This could mean that the Cooling Fans are not functioning. Assure that all fans are operating properly.
What is the treatment for these problems?
There are 2 simple approaches:
1) To stand the console vertically. Put the console on its side and then cross the armsInsert the feet if your console is laying horizontally, when the console is laying vertically, put the feet beneath the box and lift the box from underneath.
2) On the other hand, lift the metal box from the left corner, about 2″ from its left side. Open the box and check if there are any screws. Remove the cover from the hard drive bay and look at the memory card device. There will be screws under the protective cover, remove the cover and look at the memory card. Then, remove the remaining screws. Just lift the remaining screws. When you look at them, it should look like a ring. Then, remove the cover and then the memory card.
3) When you look at it, the console with the 3 red lights is like a big structure made of metal. It’s cooling system is inadequate. Update the power supply strap to prevent the accumulation of heat.
4) Heat sinks should be repaired. It is the joystick.They play a vital role. It is positioned in such a way that its heat sink can suck out heat from the console. Get Rid of the dust that is found building up in the holes. When the front glass is broken, the hot air circulates and leaves the area covered with dust. Ensure that the console is placed in an open space and the heat can pass away.\
Leave a Reply